Axis 1 Spezifikationen PDF herunterladen

MOUNTING TEMPLATE

ENGLISH

INSTALLATION

1. Affix the mounting template at the desired mounting position.

2. Drill two mounting holes of ø3.4mm (ø1/8”).

3. To pass the cable through to the header, drill a wiring hole of ø8mm (ø5/16”).

4. Remove the mounting template.

5. Remove the housing cover. Attach the sensor to the mounting surface with two mounting screws.

The sensor mounting position may be limited depending on the header thickness and the mounting height.

NOTE

CAUTION

Risk of getting caught.

Make sure to affix the mounting template as described in the above chart.

Otherwise, it can be dangerous since there may be no presence detection area

around the threshold. Install the sensor as low as possible on the header.

1.Plug the connector of the sensor.

2.Supply power to the sensor. Adjust the detection area and set the dipswitches. (See ADJUSTMENTS)

Place the housing cover .

If wiring is to be exposed, break the knockout.

WARNING

Danger of electric shock.

Do not use the sensor without the cover.

When using the cable knockout, install the sensor indoors or use the rain-cover

(Separetely available) otherwise electric shock or breakdown of

the sensor may occur.

MANUFACTURER'S STATEMENT

WARNING

Do not wash, disassemble, rebuild or repair the sensor, otherwise

it may cause electric shock or breakdown of equipments.

Danger of electric shock.

WARNING

CAUTION

NOTE

Disregard of warning may cause the improper operation causing death or serious injury of

person.

Special attention is required to the section of this symbol.

Disregard of caution may cause the improper

operation

causing injury of person or damage to

objects.

NOTE

Read this operation manual carefully before use to ensure proper operation of the sensor.

Failure to read this operation manual may cause improper sensor operation and may result in serious injury or death of

person.The meanings of the symbols are as follows. Please study the following first and then read the contents of this

operation manual.

1. This sensor is a non-contact switch intended for header mount / wall mount of an automatic door.

Do not use for any other applications. This sensor cannot be used for industrial doors or shutters,

when used, proper operation and safety cannot be guaranteed.

2. When setting the sensor's detection area, make sure there is no traffic around the installation site.

3. Before turning the power on, check the wiring to prevent damage or malfunction of equipments that are connected

to the sensor.

4. Only use the sensor as specified in the operation manual provided.

5. Be sure to install the sensor in accordance with the local laws and standards of the country in which the sensor is

installed.

6. Before leaving the job site make sure that the sensor is operating properly and instruct the building owner/operator

on proper operation of the door and the sensor.

7.The sensor setting can only be changed by an installer or service engineer. When changed, register the changed

　setting and dates in the maintenance logbook accompanying the door.

The following conditions are not suitable for the sensor installation.

-Fog or exhaust emission around the door.

-Wet floor

-Vibrating header or mounting surface.

-Moving objects or a heating radiator in the detection area.

-Highly reflecting floor or the presence of highly reflecting objects around the door.

NOTE

H: Height from the floor to the bottom of the header

Distance between the bottom of header and the sensor.

X: Distance between the door and the mounting surface

Sensor

Door

Header

Floor

Maximum mounting distance (Y)

[mm(feet,inch)]

WARNING

Before starting the procedure, ensure that the power is turned OFF.

When passing through the cable to the hole, make sure not to tear the shield,

otherwise it may cause electric shock or breakdown of the sensor.

Danger of electric shock.

NOTE

Make sure to connect the cable correctly to the door controller before turning the power ON.

To enable the presence detection, do not enter the detection area for 10 seconds after supplying the power.

SPECIFICATIONS

Model

Cover color

Mounting height

Detection area

Detection method

Depth angle adjustment

Power supply

Power consumption

Operation LED

: OA-AXIS I / OA-AXIS II

: Silver / Black

: 2.0 (6'7") to 3.5m (11'5")

: See DETECTION AREA

: Active Infrared Reflection

: 1st to 3rd rows / -6 to +6

4th and 5th rows / +26 to +44

: 12 to 24VAC( 10%)

12 to 30VDC( 10%)

: OA-AXIS I < 3VA

OA-AXIS II < 4VA

: Green / Stand-by

Blinking Red / 1st row detection

Red / 2nd row detection

Orange / 3rd to 5th rows detection

Output

Output hold time

Response time

Operating temperature

IP rate

Weight

Accessories

: OA-AXIS I /

Form C relay

50V 0.3A Max.(Resistance load)

OA-AXIS II /

　 1st to 3rd rows / Form C relay

50V 0.3A Max. (Resistance load)

3rd to 5th rows / Form C relay

50V 0.3A Max.(Resistance load)

: Approx. 0.5 sec.

: <0.3 sec.

: -20 to +55 C(-4 to 131 F)

: IP44

: 320g (11.2oz)

: 1 Cable 3m (9'10")

1 Operation manual

2 Mounting screws

1 Mounting template

1 Area adjustment tool

The specifications herein are subject to change without prior notice due to improvements.

NOTE

OUTER DIMENSIONS AND PART NAMES

62.3(2 7/16")

267(10 1/2")

45(1 3/4")

7.5(5/16")

6°-6°

26°

44°

Snow

Mode

Immunity

PRESENCE

OFF

ACTIVATION

Narrow

Shallow Deep

1,2

Low

Middle

High

S-High

Sensitivity

3,4

15sec.

60sec.

180sec.

∞

Presence

Timer

5,6

Frequency

7,8

Row

Adjustment

5 rows

4 rows

3 rows

2 rows

Depth

6°

-6°

44°

26°

Depth

Width

Not applicable

0°

35°

-3° 3°

39.5°30.5°

5730350

1 2 3 4 6 7 8 9 10 11 12 14 15 16135

Wide

Narrow

Wide

Installation

Mode

OFF

(1)

(5)

(4)

(6) (7)

(3)

125(4 15/16")

36(1 7/16")

43(1 11/16")

(2)

(8)

(1) Connector

(2) Mounting holes

(3) Operation LED

(4) Depth angle adjustment screw

(5) Width adjustment screws

(6) Dipswitches

(7) Detection window

(8) Area adjustment tool

[mm (inch)]

DETECTION AREA

The actual detection area may become smaller depending on the ambient light, the color / material of the

object or the floor as well as the entry speed of the object.

NOTE

OA-AXIS I

OA-AXIS II

}

Grey

White

Yellow

Green

Power supply

12 to 24VAC　10％

12 to 30VDC 10%

Common (COM.)

Normally open (N.O.)

Normally closed (N.C.)

}

Grey

White

Yellow

Green

Common (COM.)

Normally open (N.O.)

Normally closed (N.C.)

White Str.

Yellow Str.

Green Str.

Common (COM.)

Normally open (N.O.)

Normally closed (N.C.)

Power supply

3rd to 5th

rows output

1st to 3rd

rows output

Wire the cable to the door controller properly as shown in the drawing below.

12 to 24VAC　10％

12 to 30VDC 10%

[m(feet,inch)]

2.20(7'2 5/8")

0.14(5 1/2")

0.42(1'4 9/16")

0.82(2'8 5/16")

1.35(4'5 1/8")

1.90(6'2 13/16")

2.50(8'2 7/16")

0.16(6 5/16")

0.48(1'6 7/8")

0.93(3' 5/8")

1.54(5' 5/8")

2.17(7'1 7/16")

1.33(4'4 3/8")

2.05(6'8 11/16")

1.51(4'11 7/16")

2.32(7'7 5/16")

2.78(9'1 7/16")

3.15(10'4")

2.70(8'10 5/16")

0.18(7 1/16")

0.52(1'8 1/8")

1.00(3'3 3/8")

1.66(5'5 3/8")

2.34(7'8 1/8")

3.00(9'10 1/8")

0.20(7 7/8")

0.58(1'10 13/16")

1.10(3'7 5/16")

1.85(6' 13/16")

2.60(8'6 3/8")

1.63(5'4 3/16")

2.51(8'2 13/16")

1.81(5'11 1/4")

2.79(9'1 13/16")

3.40(11'1 7/8") 3.79(12'5 3/16")

3.50(11'5 13/16")

0.23(9 1/16")

0.67(2'2 3/8")

1.30(4'3 3/16")

2.16(7'1 1/16")

3.03(9'11 5/16")

2.11(6'11 1/16")

3.26(10'8 3/8")

4.42(14'6")

OA-AXIS I / II

5915031 JAN 2009

*The outputs from the 3rd row overlaps.

1st row

2nd row

3rd row

4th row

5th row

: Emitting spots

: Detection area

Sensor setting

1st to 3rd rows : +6

4th and 5th rows : +44

Motion / Presence

detection

Motion detection

: Emitting spots

(Can be elminated)

*The values of the chart above is of the emitting spots, but not of the detection area.

2,000 (6' 6") 2,200 (7' 2") 2,500 (8' 2") 3,000 (9' 10")

No limit

50 (1 15/16") 200 (7 7/8") 200 (7 7/8") 200 (7 7/8")

100 (3 15/16") 200 (7 7/8") 200 (7 7/8") 200 (7 7/8") 200 (7 7/8")

150 (5 7/8") 130 (5 1/8”) 150 (5 7/8”) 170 (6 11/16") 200 (7 7/8")

200 (7 7/8")

- 110 (4 5/16”) 130 (5 1/8”) 150 (5 7/8”)

250 (9 13/16") 120 (4 3/4”)

300 (11 13/16") - -

200 (7 7/8")

- -

1 2 3 4

Inhaltsverzeichnis

Seite 1 - OA-AXIS I / II

MOUNTING TEMPLATE21ENGLISH34INSTALLATION1. Affix the mounting template at the desired mounting position.2. Drill two mounting holes of ø3.4mm (ø1/8”).

Seite 2 - Front view

1ADJUSTMENTS2Make sure the detection area does not overlap with the door / header,otherwise ghosting / signal saturationmay occur.Do not place any hig

Seite 3 - OA-AXIS T

45(1 3/4")63(2 1/2")267(10 1/2")125(4 15/16") 36(1 7/16") 43(1 11/16") 7(1/4")1st to 3rd rows4th and 5th rowsNarro

Seite 4 - East Coast Office

Mounting height [ m (feet,inch) ]2.0 (6' 6") 2.2 (7' 2") 2.5 (8' 2") 3.0 (9' 10")Contact your installer or ser