Axis 1 Spezifikationen PDF herunterladen (Seite 4)

Mounting height [ m (feet,inch) ]

2.0 (6' 6") 2.2 (7' 2") 2.5 (8' 2") 3.0 (9' 10")

Contact your installer or service engineer.

Sensor failure

ADJUSTMENTS

Wrong wiring or connection failure Check the wires and connector.

Wrong wiring or connection failure

Check the wires and connector.

Door operation

Operation

indicator

Possible cause

Possible countermeasures

None Wrong power supply voltage Set to the stated voltage.

Wrong wiring or connection failure

Fast

Green

blinking

Signal saturation (1st or 2nd row)

Dirty detection window Wipe the detection window with a damp cloth.

(Do not use any cleaner or solvent.)

Sensitivity is too low.

Set the sensitivity higher.(*)

The detection area overlaps with

the door / header.

Adjust the detection area to "Deep" (Outside).

Door opens

when no one

is in the

detection area.

(Ghosting)

Unstable

Door remains

open

Sudden change in the detection area

Check ADJUSTMENTS 3-1 & 3-2.(*)

If the problem still persists, hard-reset the

sensor.(Turn the power OFF and ON again.)

Slow

Green

blinking

Check the wires and connector.

Remove highly reflecting objects from the

detection area. Or lower the sensitivity.(*)

Or change the area depth angle for 1st to 3rd rows.

Wrong setting of dipswitch

Red &

Green

blinking

Door does not

open when a

person enters

the detection

area.

Unstable

Wrong detection area positioning

Check ADJUSTMENTS 1 , 2 & 3.(*)

Sensitivity is too low.

Set the sensitivity higher.(*)

Short presence detection timer

Set the presence detection timer longer.(*)

Proper

Wrong setting of dipswitches. Check ADJUSTMENTS “3-6”- “3-10”.(*)

Dirty detection window Wipe the detection window with a damp cloth.

(Do not use any cleaner or solvent.)

Wrong setting of function key Set to the"Operation mode".

When using more than two sensors close to each other, set the different

frequency for each sensor by dipswitches 5 and 6.

3-3.Setting the frequency

3-5.Setting the immunity

Red

4th and 5th rows

Area depth angle adjustment

1st to 3rd rows

Area adjustment tool

Area width adjustment

Blue

Use the area adjustment tool (B) as shown above to

change the area depth angle for the 4th and 5th rows.

Depth angle adjustment screw

for the 1st to 3rd rows

Depth angle adjustment screw

for the 4th and 5th rows

Use the area adjustment tool (A) as shown above to

change the area depth angle for the 1st to 3rd rows.

1-2.Simultaneous adjustment

1-1.Independent adjustment

For the simultaneous adjustment of the 1st to 5th rows, use the adjustment tool (C).

When adjusting the width adjustment screws, make sure to turn until it clicks otherwise the proper operation may not

be obtained.

cannot be eliminated separately, neither can .

Depth angle

adjustment screw

Shallow

Deep

4th and 5th rows 1st to 3rd rows

Width adjustment

screws (Right)

Width adjustment

screws (Left)

Check the operation in the operation mode according to the chart below.

Dipswitch settings

Refer to the chart below for the suitable sensitivity to your installation environment.

3-1.Setting the sensitivity

3-2.Setting the presence detection timer

The 1st and 2nd rows have the presence detection function.

To comply with DIN 18650, set the timer to " 60sec." or more.

To enable the presence detection, do not enter the detection area for 10 seconds after setting the timer.

When adjusting the 1st row close to the door,

follow 3-11 Installation mode for the easier adjustment.

Special attention to the setting is required when the door is used often by the elderly or children.

Please adjust the sensitivity and the presence detection timer according to your risk assessment.

For example

Floor condition

Low reflection

Middle Middle

High

S-High

-Carpet

-Dark color floor

Middle reflection

Low Middle Middle

-Concrete

High reflection

Low

Middle High

-Tile

-Marble

S-High

1. Always keep the detection window clean. If dirty, wipe the window with a damp cloth.(Do not use any cleaner / solvent.)

2. Do not wash the sensor with water.

3. Do not disassemble, rebuild or repair the sensor yourself, otherwise electric shock may occur.

4. When the operation indicator blinks Green, contact your installer or service engineer.

5. Always contact your installer or service engineer when changing the settings.

6. Do not paint the detection window.

WARNING

1. When turning the power ON, always walk-test the detection area to ensure the proper operation.

2. Do not place any objects that move or emit light in the detection area. (e.g. Plant, illumination, etc.)

When the above procedures (1-3) are not followed, an error (Red & Green blinking) occurs.

Make sure to use the sensor only in the" Operation mode".

The sensor does not operate properly in the "Setting mode".

Follow these steps to change the settings of dipswitches.

1.Change the function key from the "Operation mode" to the "Setting mode".

During the "Setting mode", the operation indicator is blinking Blue

(only when stand-by status) and the door remains open.

2.Change the dipswitch settings.

3.When the setting is finished, change the function key back to the "Operation mode".

Function key

Operation mode

Setting mode

Set the depth rows with dipswitches 7 and 8.

3-4.Setting the row adjustment

When "2rows" are selected, the activation output

is disabled.

Make sure that the detection area does not overlap with the door / header, and there is no highly reflecting

object near the detection area otherwise ghosting / signal saturation may occur.

NOTE

INFRARED FINDER

Detection area

1. Turn the depth angle adjustment screw to the right (Deep) to place the detection area most away from the door.

2. Set INFRARED FINDER sensitivity to "H" (High) and place it on the floor as shown below.

Area depth adjustment with INFRARED FINDER (Separately available)

REFERENCE

3. Turn the depth angle adjustment screw to the left (Shallow) until the emitting area is placed at the position where

INFRARED FINDER is in the low detection status (Slow Red blinking).

Set dipswitch 9 to ON when the sensor operates by itself (Ghosting).

ONOFF

Setting1

Setting2

Setting3

Setting4

Low

Middle

High

S-High

30sec.

60sec.

180sec.

5rows

4rows

3rows

2rows

CHECKING

INFORM BUILDING OWNER / OPERATOR OF THE FOLLOWING ITEMS

TROUBLESHOOTING

1. Set the function key to the "Setting mode".

2. Change the dipswitch 16 setting (ON OFF or

OFF ON OFF).

3. Set the function key back to "Operation mode".

Blinking Blue

NOTE

When dipswitch 9 is set to ON ,the actual detection area may become smaller.

Proper

operation

Others Set the immunity to ON.(*)

Adjust the detection area to "Deep" (Outside).

Waterdrops on the detection window Use the rain-cover (Separately available).

Or install in a place keeping the waterdrops off.

The detection area overlaps

with that of another sensor.

Detection area overlaps with door /

header.

Check ADJUSTMENTS 3-3.(*)

Objects that move or

emit light in the detection area.

Remove the objects.

Sensitivity is too high. Set the sensitivity lower.(*)

Installation mode is set to ON. Set installation mode to OFF.(*)

Yellow

* Before changing these settings, set the function key to the "Setting mode". When finished, set back to the "Operation mode".

Remove highly reflecting objects from the

detection area. Or lower the sensitivity.(*)

Or change the area depth angle.

Signal saturation (3rd, 4th or 5th row)Slow

Green

blinking

Shallow

Deep

ShallowDeep

[m]

1.0

2.0

3.0

2.0

3.0

[m]

1.0

2.0

3.0

1.0

2.0

ShallowDeep

[m]

2.0

3.0

1.0

2.0

3.0

2.0

3.0

Status

Green

Motion

detection active

Red

Blinking Red

Entry

Outside of

detection

area

Outside of

detection

area

Entry into

3rd to 5th row

Entry into

2nd row

Entry into

1st row

Orange

Stand-by

Green

Stand-by

Operation indicator

Motion / Presence

detection active

Power OFF

None

Activation

output

Safety

/ Test

output

ON OFF ONOFF

OFF ON OFFOFF

High

Low

N.O.

N.C.

Front view

[m]

2.0

3.0

02.0 1.0 2.01.0

1 2 3

5 6 7

9 10 11

Narrow

Wide

Eliminated

Narrow

Wide

Eliminated

1 2 3 10 11 12

3-6.Setting the self monitoring

Disable Enable

When the door remains open and the LED indicator shows fast or slow green

blinking, please refer to the TROUBLESHOOTING.

If the door still remains open, set dipswitch 10 to "Disable".

To comply with DIN18650 dipswitch 10 must be set to "Enable".

NOTE

3-7.Setting the Safety / Test output (to door controller)

3-8.Setting the test input (from door controller)

3-11.Installation mode

Set dipswitch 16 to ON when adjusting the 1st row close to the door.

When the setting is finished, set to OFF.

During the installation mode, only the 1st row remains, and the operation indicator glows Yellow.

3-10.Setting the activation output

Set dipswitch 14 to "N.O." (Normally Open) or "N.C." (Normally Closed) .

NOTE

If the function key is set back to the "Operation mode" while the installation mode is still ON, an error occurs.

N.C.N.O.

UniBi

ONOFF

Low

High

Low

High

3-9.Settings the direction recognition

When Dipswitch13 is "Uni", uni-directional function is activated.

This function enables the door to close earlier if a person walks away from the door.

Uni-directional function is disabled in case presence area detection continues more than 5sec.

NOTE

The delay time between test input and Safety / Test output is 10msec.

Dipswitch11 is the Safety / Test output (to door controller).

Dipswitch12 is the test input (from door controller).

OPTEX Technologies Inc.

Corporate Headquarters

North and South American Subsidiary

3882 Del Amo Blvd., Suite 604 Torrance, CA 90503 U.S.A.

TOLL-FREE: 800 877 6656 FAX.: +1 310 214 8655

WEBSITE: www.optextechnologies.com

East Coast Office

OPTEX Co.,LTD. OPTEX Technologies B.V.

Manufacturer European Subsidiary

5-8-12 Ogoto Otsu 520-0101, Japan

TEL.: +81(0)77 579 8700 FAX.: +81(0)77 579 7030

WEBSITE: www.optex.co.jp/as/eng/index.html

Tiber 2, 2491 DH The Hague, The Netherlands

TEL.: +31(0)70 419 41 00 FAX.: +31(0)70 317 73 21

E-MAIL: [email protected] WEBSITE: www.optex.nl

8510 McAlpines Park Drive, Suite 108 Charlotte,

NC 28211 U.S.A.

TOLL-FREE: 800 877 6656 FAX.: +1 704 365 0818

WEBSITE: www.optextechnologies.com

1 2 3 4

Kommentare zu diesen Handbüchern

Keine Kommentare

Axis 1 Spezifikationen Seite 4

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kamerazubehör Axis 1