Axis 1 Spezifikationen PDF herunterladen (Seite 2)

ADJUSTMENTS

Make sure the detection area does not overlap with the door / header,otherwise ghosting / signal saturation

may occur.

Do not place any highly reflecting objects in the detection area, otherwise signal saturation may occur.

NOTA

NOTE

1. Always keep the detection window clean. If dirty, wipe the window lightly with a damp cloth.

(Do not use any cleaner or solvent.)

2. Do not wash the sensor with water.

3. Do not disassemble, rebuild or repair the sensor yourself, otherwise electric shock may occur.

4. When an operation LED blinks green, contact your installer or service engineer.

5. Always contact your installer or service engineer when changing the settings.

6. Do not paint the detection window.

WARNING

NOTA

NOTE

1. When turning the power on, always walk-test the detection area to ensure proper operation.

2. Do not place any objects that move or emit light in the detection area. (e.g. Plant, illumination, etc.)

INFORM BUILDING OWNER / OPERATOR OF THE FOLLOWING ITEMES

CHECKING

Check the operation according to the chart below.

Status

Green

Motion

detection active

Red

Blinking Red

Motion/Presence

detection active

OA-AXIS I

OA-AXIS

Output

Entry

Outside of

detection

area

Entry into

4th or 5th row

Entry into

3rd row

Entry into

2nd row

Entry into

1st row

Orange

Stand-by

Operation LED

Presence

detection

White Str. : COM.

Yellow Str. : N.O.

Green Str. : N.C.

White : COM.

Yellow : N.O.

Green : N.C.

Power off

None

*The outputs from the 3rd row overlaps.

Output from

3rd to 5th

rows

Output from

1st to 3rd

rows

OFF

3-7 Installation mode

Use this switch to ON when adjusting the presence detection area

close to the door face.

* During the installation mode, only the 1st row remain.

* Door open state

* Operation LED glows yellow.

Dipswitch settings

4 5 6

1,2 ：Sensitivity

3,4 ：Presence detection timer

5,6 ：Frequency

7,8 ：Row adjustment

11 to 15

Not applicable

: Snow mode

: Immunity

: Not applicable

: Installation mode

INFRARED FINDER

Detection area

1. Turn the depth adjustment screw to the right (Deep) to place the area most away from the door.

2. Set INFRARED FINDER sensitivity to "H" (High) and place it on the floor as shown below.

Area depth adjustment with INFRARED FINDER (Separately available)

REFERENCE

3. Turn the depth adjustment screw to the left (Shallow) until the emitting area is placed at the position where

INFRARED FINDER is in the low detection status (Slow Red blinking).

TROUBLESHOOTING

When using more than two sensors close to each other, set the different

frequency for each sensor by combining dipswitch 5 and 6.

3-3 Setting the frequency

Red

Shallow

Deep

Blue

4th and 5th rows

Area depth angle adjustment

1st to 3rd rows

Area adjustment tool

1st to 3rd rows

adjustment

4th and 5th rows and

area width adjustment

Width detection area adjustment

Use the area adjustment tool (B) as shown above and

change the depth of the detection area by turning the depth

angle adjustment screw.

Depth angle adjustment screw

for 1st to 3rd rows

Depth angle adjustment screw

for 4th and 5th rows

Use the area adjustment tool (A) as shown above and

change the depth of the detection area by turning the depth

angle adjustment screw.

The detection area depth can be changed by

the area adjustment tool.

1-2. Simultaneous adjustment

Simultaneous

adjustment

1-1. Independent adjustment

For the simultaneous adjustment of 1st to 5th rows, use the adjustment tool (C).

The actual detection area may become smaller depending on the ambient light, the color / material of the object and

the floor as well as the entry speed of the object.

Depth angle

adjustment screw

Shallow

Deep

Narrow

Wide

Narrow

Wide

4th and 5th rows

1st to 3rd rows

Width adjustment

screw (Right)

Width adjustment

screw (Left)

Eliminated

1210

Eliminated

１

３

Eliminated

1210

Eliminated

１

３

ShallowDeep

Normally set to "Middle". " Low" decreases the sensitivity and "High / S-High"

increases the sensitivity.

3-1 Setting the sensitivity

3-2 Setting the presence detection timer

The 1st and 2nd rows have the presence detection function.

The presence detection timer can be selected from 4 settings.

3434 34 34

15 sec. 60 sec. 180 sec.

Low Middle High

12 12

S- High

To enable the presence detection, do not enter the detection area for 10 seconds after setting the timer.

Setting 1

Setting 2

Setting 3

Setting 4

56 56

When adjusting the 1st to 3rd rows close to the door, follow 3-7 Installation mode.

[m][m]

１

７８

９

２

３

４

６

５

Front view

[m]

Check the area position with Red LED of the Operation LED using a tool such as a reflecting mirror.

7 8

5 rows 4 rows 3 rows 2 rows

7 8 7 8 7 8

The 5th, 4th, and 3rd rows can be eliminated by

combining dipswitches 7 and 8.

*When 2 rows setting is selected, only the

presence detection area remains.

3-4 Setting the area depth

Always check the area according to the expected entry speed and determine the appropriate number

of rows.

When setting motion and motion / presence detection area sparately, make sure that there is no gap between

two areas.

NOTE

Set this switch to ON, if the sensor is used in a region with snow.

3-5 Setting the snow mode

OFF

3-6 Setting the immunity

OFF

Set this switch to ON, when less influence by the header vibration is required.

Wrong wiring or connection failure.

Check the wires and connector.

Wrong wiring or connection failure.

Check the wires and connector.

Sensitivity is too high. Set the sensitivity lower.

Remove the objects.

Adjust the detection area to "Deep" (Outside).

Problem

Operation

LED

Possible cause

Possible countermeasures

None Power supply voltage. Set to the stated voltage.

Wrong wiring or connection failure.

Twice

Green

blinking

Signal saturation

The relay is reaching the end of its

life cycle.

Contact your installer or the sales engineer.

The detection area overlaps with

the door / header.

Adjust the detection area to "Deep" (Outside).

Door opens

when no one

is in the

detection area.

(Ghosting)

Unstable

Vibration of the header. Set the sensitivity lower or the immunity to ON.

Water drops on the detection window. Use the rain-cover (Separately available).

Or install in a place keeping the waterdrops off.

The detection area overlaps

with that of another sensor.

The detection area overlaps

with the door / header.

Reflecting objects in the detection area.

Or reflecting light on the floor.

Door remains

open

Red

Orange

Sudden change in the detection area.

Check ADJUSTMENTS 3-1 & 3-2.

If the problem still persists, hard-reset the

sensor.(Turn the power OFF and ON again.)

Slow

Green

blinking

Check the wires and connector.

Remove highly reflecting objects from the

detection area. Or lower the sensitivity.

Or change the area angle.

Check ADJUSTMENTS 3-3.

Door does not

open when a

person enters

the detection

area.

Unstable

Wrong detection area positioning.

Check ADJUSTMENTS 1 & 2.

Sensitivity is too low.

Set the sensitivity higher.

Short presence detection timer.

Set the presence detection timer longer.

Door remains

closed

Proper

Dirty detection window. Wipe the detection window with a damp cloth.

(Do not use any cleaner or solvent.)

It snows and pours.

Set the snow mode to ON.

Remove the objects.

Wet floor. Check the installation condition referring to

INSTALLATION on the reverse side.

The exhaust emission or fog pen-

etrate into the detection area.

Objects that move or emit light in the

detection area.

(Ex.Plant, illumination,etc.)

1 2 3 4

Kommentare zu diesen Handbüchern

Keine Kommentare

Axis 1 Spezifikationen Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kamerazubehör Axis 1