Axis Q6035-E Bedienungsanleitung PDF herunterladen (Seite 23)

AXIS Q6035–E PTZ Dome Network Camera

PTZ (Pan Tilt Zoom)

OSDI zones are set up under PTZ > OSDI Zones. The Axis product uses the coordinates of the center of the view to set the lower

left and upper right zone areas. First navigate to where you would like the lowermost left point of the OSDI zone to be located.

Click Get to set the coordinates. Proceed to where the upper right point of zone should be located and click Get. Give the zone a

descriptive name and click OK.

To include the name of the OSDI zone in the overlay text, go to Video < Video Stream < Overlay Settings.ChecktheInclude

text box and enter the modiﬁer #L in the ﬁeld. For more inform ation about modiﬁers, see

File Naming & Date/Time Formats

theonlinehelp

Advanced

Limits

Deﬁne the pan, tilt, zo om and focus limits for the Axis p roduct. Movements to the left and right, up and down, can be restricted to

narrow the area under surveillance.

Conﬁgure the near focus limit to avoid focusing on objects too close to the camera lens.

Move speed sets the speed of the camera’s pan and tilt movements. The default setting is maxim u m speed.

When using a jo ystick (or emulating one with the mouse) the Enable proportional speed setting can be used to reduce the maximum

pan/tilt movement speed, i.e. the speed the ca m er a view moves at when the joystick is pushed all the way out in any direction. This is

useful then the view is zoomed in on an object.

When Enable Auto-ﬂip is selected, the Axis product will simulate continuous pan movement in the same direction, i.e. the camera

will pan the full 360 degrees, even though there is a mechanical stop at ±180 degrees.

When Enable movement prediction is selected, the Axis p roduct will attempt to predict the new position in the pan movem ent, after

compensating for the slight delay while the camera changes direction after an auto-ﬂip. This is useful for tracking moving objects or

persons when using the joystick or emulated joystick mode.

See the online help

for more information.

Controls

Panel Shortcut Command Buttons can be conﬁgured to provide direct access to commands issued via the VAPIX® Ap plication

Programming Interface. The buttons will be displayed in the PTZ c ontro l panel, which is available in the Live View page though

the Ctrl panel button, see

page 9

Deselect the options under Enable/Dis

able controls to disable the pan, tilt, zoom, focus and iris controls.

Note

Disabling PTZ controls will affe ct preset positions. Fo r example, if the tilt control is disabled, the product cannot move to

preset positions that require a tilt movement.

Control Queue

The administr

ator can set up a queue for PTZ controllers from PTZ > Control Q ueue. Once s et up, the PTZ Control Queue buttons

appear in the Live View pag e of fering one viewer exclusive control for a limited period of time. Other users will be placed in queue.

A user who belo ngs to a group (see

Users, on page 33

) w ith a higher PTZ priority can go before other users in the queue and

take control of the product. The order of priority is as follows:

1. Administrator — An administrator takes over PTZ control regardless of who is ﬁrst in queue. The administrator w ill be

removed from the queue 60 seconds after the last PTZ control command.

2. Event — The Axis product can be conﬁguredtogotoapresetpositionwhen triggered by an alarm (see

Events, on page 26

The event w ill immediately be placed ﬁrst in the queue except when an administrator is in control.

3. Operator — Same as administrator but with lower priority

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 49 50

Kommentare zu diesen Handbüchern

Keine Kommentare

Axis Q6035-E Bedienungsanleitung Seite 23

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitskameras Axis Q6035-E